rev. 1.0 1/15 copyright ? 2015 by silicon laboratories AN843 AN843 using analog components to manage power in low-power solar systems 1. introduction from large panels to harvested microwatts from a few photodiodes, solar power is increasingly prevalent in autonomously powered systems. with the worldwide evol ution toward lower power operation using more ?green? energy sources, emphasis on deploying solar power in a greater variety of environments has been on the rise. in low-power solar systems, it is critic al to assess whether there is sufficient sunlight at a given time to power the system. in some cases, this involves determining whether there is sufficient po wer to enable the microcontroller. in many ultra-low-power systems, the simple act of waking the microcontroller to make a voltage measurement might collapse the solar source or waste precious power from a reservoir capacitor. one solution is to incorporate a si mple analog op amp into the system. an ultra-low- power analog op amp can support ?always-on? circuitry around the microcontroller and may be the simplest and best solution. 2. ultra low-power op amps figures 1 to 3 illustrate a few simple circuits using an ultra-low-power op amp in a continuous ?always-on? measurement mode assessing the state of the solar cell. the technique hangs on using an op amp whose total power is as low as practical driven primarily by ultra-low supply voltage operation. the circuit in fig. 1 shows a photodiode in photovoltaic zero-bias mode. the short-circuit current is measured and converted to a voltage across resistor r1 while the feedback action of the op amp forces 0 v across d1. zero-bias photovoltaic current is a convenient parameter that is generally well characterized and can be directly referenced to most photodiode manufacturer datash eets. note that with the rail-to-rail input range of the analog op amp, in this case the ts1001 op amp, the photodiode may be conne cted directly to the positive supply voltage rail. figure 1. an ultra-low-power op amp can be in a continuous ?always- on? measurement mode the circuit in figure 2 generates a simple positive-polar ity output for a similar zero-bias-mode measurement. in this case, the op amp servos its output to sink sufficie nt current to support the zero bias condition for d1. this creates a voltage across resistor r1 at the negative supply voltage pin of the ts1001. since this ultra-low-power op amp contributes less than 1 a to this current, the current measured from d1 has minimal error.
AN843 2 rev. 1.0 figure 2. an ultra-low-power op amp offers simple, positive polarity output to support a zero bias condition for a more comprehensive assessment, the circuit in fig. 3 tests the solar source to see if it can handle the load. the circuit shown makes this assessment without burdeni ng the microcontroller and risking collapse of the supply during measurement. figure 3. an ultra-low-power op-amp-based circuit assesses a pv solar-cell source approximately once per 100 ms, the circuit disconnects th e solar-cell power source from its reservoir capacitor and load, applying a test load (r1) and assessing the resulting voltage drop. if the voltage drops 25% or more, the result is latched into u2 and the power status is provided to the microcontroller. this ultra-low power circuit draws less than 3 a at 1 v. op amp u1 provides the timer function and controls transistor switches t1 and t2 to a pply the test load while simultaneously disconnecting the load. capacitor c1 temporarily holds the voltage to keep this circuitry and any standby loads powered. op amp u2 serves as a comparator, tripping when the power source drops more th an 25% (with 5% hysteresis). transistor t3 latches the result, while transistor t4 resets the latch during each assessment period to ensure a fresh reading. such test loading is useful for dete rmining the available power from a solar cell, since merely measuring the open circuit voltage generally does not provide an accurate assessment.
AN843 rev. 1.0 3 2.1. assessing ?alw ays-on? circuitry generally, an ultra-low-power op amp, like the ts1001, is an excellent option for supporting ?always-on? analog circuitry. for example, op amps that are guaranteed to operate under 1 v and consume less than 1 a current may be configured as a filter and left continually on, so that a microcontroller making an adc measurement does not have to stay powered on while the filter settles. in conclusion, ultra-low-power op amps are useful in lo w-power solar systems to as sess the available power from solar cells before a load is applied, and generally to support standby, ?always-on? circuitry, while drawing negligible currents. for additional information, se e the documentation for the ts10 01 or contact silicon labs.
disclaimer silicon laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the silicon laboratories products. characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "typical" parameters provided can and do vary in different applications. application examples described herein are for illustrative purposes only. silicon laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. silicon laboratories shall have no liability for the consequences of use of the information supplied herein. this document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. the products must not be used within any life support system without the specific written consent of silicon laboratories. a "life support system" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. silicon laboratories products are generally not intended for military applications. silicon laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. trademark information silicon laboratories inc., silicon laboratories, silicon labs, silabs and the silicon labs logo, cmems?, efm, efm32, efr, energy micro, energy micro logo and combinations thereof, "the world?s most energy friendly microcontrollers", ember?, ezlink?, ezmac?, ezradio?, ezradiopro?, dspll?, isomodem ?, precision32?, proslic?, siphy?, usbxpress? and others are trademarks or registered trademarks of silicon laboratories inc. arm, cortex, cortex-m3 and thumb are trademarks or registered trademarks of arm holdings. keil is a registered trademark of arm limited. all other products or brand names mentioned herein are trademarks of their respective holders. http://www.silabs.com silicon laboratories inc. 400 west cesar chavez austin, tx 78701 usa smart. connected. energy-friendly products www.silabs.com/products quality www.silabs.com/quality support and community community.silabs.com
|
